Quick Answer
Fire alarm and sprinkler systems do different jobs, so most commercial buildings need both. Detection and alarm find a fire early and start evacuation; sprinklers control or suppress it with water; standpipes and hose systems support firefighting; and special-hazard systems such as clean agents protect rooms where water would cause unacceptable damage. The right mix comes from the building's use, the Egyptian Fire Code and the approvals for the specific premises.
What matters most
Alarm systems detect and warn; sprinklers act on the fire. They complement each other.
Water-based sprinklers come in wet, dry, pre-action and deluge configurations for different risks.
Clean-agent and other special-hazard systems suit server, electrical and archive rooms, with strict room-integrity and safety conditions.
Integration with lifts, HVAC smoke control, access control and the BMS needs to be designed and tested.
In Egypt, design follows the Egyptian Fire Code and requires civil protection approval for the premises.
Stage 01
Detection and alarm: finding the fire early
A fire detection and alarm system uses smoke, heat or flame detectors and manual call points connected to a control panel, which then sounds alarms, shows the location and triggers other actions. Addressable systems identify the exact device, which speeds response in large floors and towers. Larger buildings may add voice evacuation so that instructions can be given floor by floor.
NFPA 72 is a widely used reference for fire alarm and signalling systems. In Egypt the applicable requirements come from the Egyptian Fire Code and the approvals for the building. Detector types must suit the space: a kitchen, car park and office floor behave very differently.
Questions to resolve
- Detector type matched to each space
- Addressable panel and clear zoning
- Voice evacuation and phased evacuation strategy where required
Stage 02
Sprinklers: controlling the fire with water
Automatic sprinklers open individually when heat at the head reaches its rating, so only the heads near the fire discharge. Wet-pipe systems keep water in the pipes and are the most common in conditioned buildings. Dry-pipe systems hold air until a valve opens, for areas at risk of freezing. Pre-action systems need a detection signal before water enters the pipes, which reduces accidental discharge in sensitive spaces. Deluge systems open all heads at once for specific high-hazard areas.
NFPA 13 is the common international reference for sprinkler installation. Hazard classification, water supply, pump capacity and head spacing are engineering decisions for the designer, and changes during fit-out, such as new partitions or ceilings, can make an existing layout non-compliant.
Questions to resolve
- Hazard class of each area
- Water supply, tanks and pumps confirmed
- Sprinkler layout rechecked after fit-out changes
Stage 03
Standpipes, hose reels and extinguishers
Standpipe and hose systems give firefighters and trained occupants water outlets on each floor; in high-rise buildings they are central to the firefighting strategy. Portable extinguishers handle very small fires and must match the risk: water, foam, CO2, dry powder or wet chemical each suit different fire classes.
These are often specified as a package, but each has its own inspection and maintenance needs. The facility team should have a register of locations and service dates from day one.
Questions to resolve
- Standpipe and hose reel coverage per floor
- Extinguisher type matched to each risk
- Inspection and service register
Stage 04
Special-hazard suppression for sensitive rooms
Rooms with IT equipment, electrical switchgear, archives or valuable equipment may use a clean-agent gaseous system (NFPA 2001 is a common reference), designed to suppress fire without leaving residue. These systems depend on a sealed room that can hold the agent concentration for the design time, so room-integrity testing, door closers and sealed penetrations are part of the system.
Carbon dioxide systems are used mainly for unoccupied hazards because of the risk to people; commercial kitchens use dedicated wet-chemical hood systems. Each special system needs warning signs, abort and release arrangements and a maintenance contract.
Questions to resolve
- Room integrity and sealing for gaseous systems
- Occupant safety and warning arrangements
- Kitchen hood system where cooking is planned
Stage 05
Integration: where most problems appear
On alarm, a modern building may recall lifts, start smoke-control fans, close fire dampers, release access-controlled doors and send signals to the building management system. Each link is a cause-and-effect rule that must be written into a matrix, built and then tested end to end. A system that passes on its own can still fail as part of the building.
AIG's separate guide on commercial fire protection covers design, commissioning and handover in detail. Use it with this selection guide when preparing a tender or fit-out brief.
Questions to resolve
- Cause-and-effect matrix approved
- Integrated end-to-end test witnessed
- Records handed to the facility team
Direct AIG Contact
Planning fire protection for a building or fit-out?
Share the building use, floor areas and any special rooms with AIG's team and ask for a technical discussion before you fix the specification.
First-party Context
AIG fire-protection capability and project context

AIG's published business activities include installation of fire protection systems, and its AI Tower project is presented with an integrated building technology layer from Honeywell. Fire-system choices for a particular unit or building still depend on its approved design and current authority requirements.
Practical checklist
Use these points to structure a meeting or tender enquiry. They are not a substitute for licensed local design, legal, health or engineering review.
Questions frequently raised by project teams
If a building has sprinklers, does it still need a fire alarm?
In most commercial buildings, yes. Sprinklers act on the fire; detection and alarm warn people early and trigger other safety functions. The exact requirement comes from the code and approvals.
Will sprinklers flood the whole floor?
Standard sprinklers open individually near the fire. Deluge systems are the exception and are used only for specific hazards.
Is a clean-agent system suitable for any room?
No. It needs a sealed room that holds the agent concentration and suitable safety arrangements. It is typically used for server, electrical or archive rooms.
Sources & further reading
Company project statements are based on AIG's own published material. Technical standards may require purchase and do not replace locally applicable approvals.



